Lian-Mueller Enterprises is an authorized distributor for Qualcomm Atheros Communications, 8Devices, LinkCom, Siretta & Related Products and Services, DFM

Welcome to LME

4G / LTE Analyzer Network

4G refers to the fourth generation of cellular communication technology which supersedes the global system for mobile communications standard (GSM) and high speed packet access (HSPA) standards. It offers massive improvements in data throughput and reduced latency over 2G and 3G networks as it is entirely IP based. As 4G is IP based it no longer supports circuit switched network nodes and therefore the base stations only need to support IP traffic which means that all 4G voice traffic is sent over the IP infrastructure.

As with 3G all of the benefits of the 2G and 3G system have been incorporated in to the 4G network to offer enhanced services with support for legacy applications such as SMS.

The 4G spectrum operates in a similar way to 2G and 3G with different regional areas being supported by different bands, however, the number of bands and regions compared to 2G and 3G is vastly different.

There are 44 defined bands for 4G and of these 13 bands are defined as Time Division Duplex (TDD) and 31 are defined as Frequency Division Duplex (FDD). The differences between these two standards is based around how they transmit and receive data using the shared spectrum.

TDD uses one frequency carrier to transmit and receive data over but the time for transmitting and receiving is different. With FDD two different frequencies are used to transmit and receive data but the data can be sent at the same time.

4G has a higher cost position compared to 2G and 3G but this cost is coming down as 4G / LTE technology is becoming more widely used across the world. The 4G network is split in to a number of classifications which define the mode of operation (TDD or FDD), the frequency band, the speed of operation and the number of MIMO layers. This can be seen in the table opposite.

As the IoT market does not necessarily require high data rates, the enhancements that are brought with the 4G network are normally not needed and as a result 2G has remained the favoured solution for IoT equipment developers. As with 3G a signifiant improvement offered by the 4G network over the 2G network is the network connection latency between two endpoints. This improvement means that the first byte will be received at the destination much more quickly and this means that the entire system latency will reduce. This opens the door for more real time, safety critical applications and allows for a much faster response times when sending and receiving information across the network.

Unlike 2G and 3G networks, the 4G network is being invested in heavily to provide more global coverage as well as further development of the new 3GPP version releases. In addition to this investment is being provided for category M and category NB IoT which offer lower speed connections designed for direct 2G network replacement.

 

This table below shows the defined 4G classifications.

User equipment Category Downlink (Mbit/s) Max. number of DL MIMO layers Uplink (Mbit/s) 3GPP Release
NB1 0.68 1 1 Rel 13
M1 1 1 1
0 1 1 1 Rel 12
1 10.3 1 5.2 Rel 8
2 51 2 25.5
3 102 2 51
4 150.8 2 51
5 299.6 4 75.4
6 301.5 2 or 4 51 Rel 10
7 301.5 2 or 4 102
8 2,998.60 8 1,497.80
9 452.2 2 or 4 51 Rel 11
10 452.2 2 or 4 102
11 603 2 or 4 51
12 603 2 or 4 102
13 391.7 2 or 4 150.8 Rel 12
14 3,917 8 9,585
15 750 2 or 4 226
16 979 2 or 4 n/a
17 25,065 8 n/a Rel 13
18 1174 2 or 4 or 8 n/a
19 1566 2 or 4 or 8 n/a

The table below shows all of the defined bands and the associated frequencies used with 4G / LTE network.

Band Number LTE Mode 4G LTE Common Name Frequency (MHz) Uplink (MHz) Downlink (MHz)
1 FDD IMT 2100 1920 – 1980 2110 – 2170
2 FDD PCS blocks A-F 1900 1850 – 1910 1930 – 1990
3 FDD DCS 1800 1710 – 1785 1805 – 1880
4 FDD AWS blocks A-F (AWS-1) 1700 1710 – 1755 2110 – 2155
5 FDD CLR 850 824 – 849 869 – 894
7 FDD IMT-E 2600 2500 – 2570 2620 – 2690
8 FDD E-GSM 900 880 – 915 925 – 960
10 FDD Extended AWS blocks A-I 1700 1710 – 1770 2110 – 2170
11 FDD Lower PDC 1500 1427.9 – 1447.9 1475.9 – 1495.9
12 FDD Lower SMH blocks A/B/C 700 699 – 716 729 – 746
13 FDD Upper SMH block C 700 777 – 787 746 – 756
14 FDD Upper SMH block D 700 788 – 798 758 – 768
17 FDD Lower SMH blocks B/C 700 704 – 716 734 – 746
18 FDD Japan lower 800 850 815 – 830 860 – 875
19 FDD Japan upper 800 850 830 – 845 875 – 890
20 FDD EU Digital Dividend 800 832 – 862 791 – 821
21 FDD Upper PDC 1500 1447.9 – 1462.9 1495.9 – 1510.9
24 FDD L-Band (US) 1600 1626.5 – 1660.5 1525 – 1559
25 FDD Extended PCS blocks A-G 1900 1850 – 1915 1930 – 1995
26 FDD Extended CLR 850 814 – 849 859 – 894
28 FDD APT 700 703 – 748 758 – 803
29 FDD Lower SMH blocks D/E 700 N/A 717 – 728
30 FDD WCS blocks A/B 2300 2305 – 2315 2350 – 2360
32 FDD L-Band (EU) 1500 N/A 1452 – 1496
33 TDD IMT 2100 1900 – 1920
34 TDD IMT 2100 2010 – 2025
35 TDD PCS (Uplink) 1900 1850 – 1910
36 TDD PCS (Downlink) 1900 1930 – 1990
37 TDD PCS (Duplex spacing) 1900 1910 – 1930
38 TDD IMT-E (Duplex Spacing) 2600 2570 – 2620
39 TDD DCS-IMT gap 1900 1880 – 1920
41 TDD BRS / EBS 2500 2496 – 2690
44 TDD APT 700 703 – 803
45 TDD L-Band (China) 1500 1447 – 1467
46 TDD U-NII 5200 5150 – 5925
47 TDD U-NII-4 (V2X) 5900 5855 – 5925
48 TDD CBRS 3600 3550 – 3700
65 FDD Extended IMT 2100 1920 – 2010 2110 – 2200
66 FDD Extended AWS blocks A-J (AWS-1/AWS-3) 1700 1710 – 1780 2110 – 2200[3]
67 FDD EU 700 700 N/A 738 – 758
68 FDD ME 700 700 698 – 728 753 – 783
69 FDD IMT-E (Duplex spacing) 2600 N/A 2570 – 2620
70 FDD AWS-4 2000 1695 – 1710 1995 – 2020
71 FDD US Digital Dividend 600 663 – 698 617 – 652

5 Item(s)

per page

Grid  List 

Set Descending Direction
  1. SIretta Snyper-5G-Graphyte

    Siretta SNYPER-5G Graphyte (GL) Cellular Network Signal Analyzer/Logger: Surveys & Logs CAT-M, NB-IoT, 2G, 3G, 4G/LTE & 5G (Global Freq Coverage) with Accessories and Hard Carry Case

    $2,239.87

    SNYPER-5G GRAPHYTE (GL)

    Cat-M, NB-IoT, 2G, 3G, 4G/LTE & 5G Signal Analyser & Datalogger

    General Description

    The SNYPER-5G Graphyte (GL) is a high performance, multi-language network signal analyser and cellular signal logger, dedicated to surveying and logging the 5G/NR 4G/LTE , LTE-Cat M, NB-IoT & 2G/GSM networks.

    It incorporates a number of important features::

    • Enhanced cellular surveying & sequential logging of new and existing installations on 5G. 4G, Cat M, NB-IoT and 2G networks
    • 5G NSA Cells Identified (Based on USER SUPPLIED SIM)
    • User selectable survey logging options to determine most suitable & reliable mobile operator
    • Evaluate “preferred” MNO’s performance over time
    • Determines “hotspots” & assist with antenna alignment, through Siretta’s liveSCAN feature
    • Results are reported in CSV, graphical HTML format & Print to PDF
    • Save over 100 logged surveys with multiple liveSCAN logs

    The unit can be left to conduct sequential surveys in a fixed location and automatically saving them. Four types of survey can be performed: a “FULL” survey (5G, 4G or CAT-M, NB-IoT, GSM combined), or a single selected technology only.

    The SNYPER-5G Graphyte is capable of detecting 5G SA Cells without requiring a 5G SIM Card. However, if you require analysing 5G NSA Cells, a valid 5G SIM card is required. The SNYPER device will then display the 5G NSA cells of the network that the SIM card operates on. This is due to the specific way 5G NSA operates.

    The U.S. National Telecommunications and Information Administration has an informative short video explaining how the 5G NR architecture is split into SA and NSA here:

    For more information on 5G Technology please click here:

    SNYPER-5G Graphyte (GL) can save a limitless amount of surveys each with different logging options and all survey results can be downloaded to a PC and displayed in a HTML graphical format to clearly show the logged detail over the survey session. This can identify unreliable base-stations & intermittent cellular service which is not possible with spot surveys. The full breakdown for the HTML summary graphs are displayed in corresponding CSV files (Summary and full detail files).

    The SNYPER-5G Graphyte (GL) also incorporates Siretta’s leading liveSCAN feature, which allows you to select a base-station signal immediately after a survey, conduct a liveSCAN logging session which can later be analysed in a CSV logged recording.

    The SNYPER-5G Graphyte (GL) is an invaluable tool for understanding local network performance over hours, days and weeks to assist in the selection of reliable mobile network operators before cellular installations.

    Contact us for volume pricing, full datasheet, Start-up Guide, training and other information.

     

    Learn More
  2. Snyper-IoT-Graphyte

    Siretta SNYPER-IOT GRAPHYTE (GL) Cellular Network Signal Analyzer/Logger: Surveys & Logs CATM / NBIoT (Global Freq Coverage) with Accessories and Hard Carry Case

    $1,329.89

    SNYPER-IOT GRAPHYTE (GL)

    Cat-M & NB-IoT Signal Analyser & Datalogger

    General Description

    The SNYPER-IoT Graphyte (GL) is a high performance, multi-language network signal analyser and cellular signal logger, dedicated to surveying and logging the LTE-Cat M, NB-IoT & 2G/GSM networks

    It incorporates a number of important features::

    • Enhanced cellular surveying & sequential logging of new and existing installations on  Cat M, NB-IoT and 2G networks
    • User selectable survey logging options to determine most suitable & reliable mobile operator
    • Evaluate “preferred” MNO’s performance over time
    • Determines “hotspots” & assist with antenna alignment, through Siretta’s liveSCAN feature
    • Results are reported in CSV, graphical HTML format & Print to PDF
    • Save 1000’s of logged surveys with multiple liveSCAN logs

    The unit can be left to conduct sequential surveys in a fixed location and automatically saving them. Four types of survey can be performed: a “FULL” survey (CAT-M, NB-IoT, GSM combined), or a single selected technology only.

    SNYPER-IoT Graphyte (GL) can save a limitless amount of surveys each with different logging options and all survey results can be downloaded to a PC and displayed in a HTML graphical format to clearly show the logged detail over the survey session. This can identify unreliable base-stations & intermittent cellular service which is not possible with spot surveys. The full breakdown for the HTML summary graphs are displayed in corresponding CSV files (Summary and full detail files).

    The SNYPER-IoT Graphyte (GL) also incorporates Siretta’s leading liveSCAN feature, which allows you to select a base-station signal immediately after a survey, conduct a liveSCAN logging session which can later be analysed in a CSV logged recording

    The SNYPER-IoT Graphyte (GL) is an invaluable tool for understanding local network performance over hours, days and weeks to assist in the selection of reliable mobile network operators before cellular installations.

    Contact us for volume pricing, full datasheet, Start-up Guide, training and other information.

     

    Learn More
  3. Siretta Snyper-LTE Graphyte (USA)

    Siretta Snyper-LTE Graphyte (USA) v2 Cellular Network Analyzer, SIM Free - Continuous Survey LTE Logger (USA)

    $1,318.00

    SIM Free - Continuous Survey LTE Logger (USA)

    SNYPER-LTE Graphyte (USA) High performance 4G / LTE signal analyser & cell logger

    General Description

    The SIM-free SNYPER-LTE Graphyte (USA) is a high performance, multi-language network signal analyser and cellular signal logger, dedicated to surveying and logging the 4G/LTE (USA) & 3G/UMTS & Cat1/Cat4 North American networks.  The unit can be left to conduct sequential surveys in a fixed location and automatically save them.  Three types of survey can be performed: a “FULL” survey (4G and 3G), 4G/LTE only & 3G/UMTS only. SNYPER-LTE Graphyte (USA) can save multiple surveys each with different logging options. All survey results can be downloaded to a PC and displayed in a HTML graphical format to clearly show the logged detail over the survey session. This can identify unreliable base-stations & intermittent cellular service which is not possible with spot surveys. The full breakdown for the HTML summary graphs are displayed in corresponding CSV files.  The SNYPER-LTE Graphyte (USA) also incorporates Siretta’s leading liveSCAN feature, which allows you to select a base-station signal immediately after a survey, conduct a liveSCAN logging session which can later be analysed in a CSV logged recording.

    *SNYPER-LTE Graphyte (USA) does not require a SIM in order to function.

    Kit includes:  SIM-free Snyper-LTE Analyzer (capable of storing 84 surveys), Plastic carrying case, Tripod & Cradle, Power Supply and Adapters, USB Cables, RF Cables, Omni and Directional Antennas.

    Contact us for volume pricing, full datasheet and other information.  EU frequency and Cat-M, NBIoT SNYPERs also available.

     

    Learn More
  4. Siretta Snyper-LTE+ (USA)

    Siretta Snyper-LTE+ (USA) v2 - Signal Strength Tester: 4G/3G/2G USA Freq Cellular Signal and Network Analyzer, version 2

    $760.76

    SIM Free - Single Survey LTE Analyser (USA)

    SNYPER-LTE+ (USA) v2 High performance 4G / LTE network signal analyser

    General Description

    The SNYPER-LTE+ (USA) v2 is a high performance, multi-language network signal analyser dedicated to surveying the 4G/LTE & 3G/UMTS & Cat1/Cat4 North American networks.  *It incorporates a number of important features and can perform three types of survey: 4G/LTE only, 3G/UMTS only, and a combined 4G & 3G survey.  The combined 4G & 3G survey will provide multiple results from each network operator, in one single survey.  The powerful SNYPER summary page displays percentage thresholds to determine the most suitable mobile network operator available and the performance of a “preferred” MNO can be evaluated against the other networks. 

    The SNYPER can also be used to help establish optimum antenna placement and perform local site surveys.

    *SNYPER-LTE+ USA v2 does not require a SIM in order to function.

     

    • 3 Supported Bands UMTS/HSPA+ (MHz): B5 (850)/B4 (1700)/B2 (1900)
    • 8 Supported Bands LTE (MHz): B71 (600)/B12-B13 (700)/B14 (700)/ B5 (850)/B4 (1700)/ B66 (1700)/ B2 (1900)

    Kit Includes:  SNYPER-LTE+ (USA) v2 Analyzer, Plastic Carry Case, Charging cable, 2 stubby antennas, car charger, power supply & adapters.

    Contact us for volume pricing, full datasheet and other information.  EU frequency and Cat-M, NBIoT SNYPERs also available.

     

    Learn More
  5. Siretta Snyper-LTEM

    Siretta Snyper-LTEM (GL) Cellular Network Signal Analyzer/Logger: Surveys & Logs on 4G(LTE) CAT M/NB IoT & 2G (Global Freq Coverage)

    $688.94

    SNYPER-LTEM (GL)

    4G/LTE Cat M, LTE Cat NB IoT, & 2G/GSM Signal Analyser & Datalogger

    Available 05/2021

    General Description

    The SNYPER-LTEM (GL) is a high performance, multi-language network signal analyser dedicated to surveying the LTE Cat M, LTE Cat NB IoT & 2G / GSM Global networks.

    It incorporates a number of important features and can perform three types of survey:

    • LTE Cat M (LTE Cat M network with signal strength in the area)
    • LTE Cat NB IoT (LTE Cat NB IoT network without signal strength in the area *)
    • 2G / GSM (2G / GSM networks with signal strength in the area)

    The LTE Cat M and LTE Cat NB IoT surveys will record the base-station with the strongest signal for each operator in the local area. The 2G / GSM survey will provide multiple results from each network operator, in one single survey.

    The powerful SNYPER summary page displays percentage thresholds to determine the most suitable mobile network operator available and the performance of a “preferred” MNO can be evaluated against the other networks.

    The SNYPER can also be used to help establish optimum antenna placement and perform local site surveys.

    * NOTE:
    The SNYPER results for the LTE Cat NB IoT network do not include the received signal strength. This is a limitation based on the internal chipset and network infrastructure interaction providing a suitable metric to measure received signal strength.

    • Enhanced cellular surveying of new and existing installations on LTE Cat M, LTE Cat NB IoT and 2G / GSM networks
    • Establish most suitable operator for application
    • Evaluate your “preferred” MNO’s performance
    • Determine optimum antenna placement
    • Results are reported in CSV & graphical HTML format

    Contact us for volume pricing, full datasheet, Start-up Guide and other information.

     

     

    Learn More

5 Item(s)

per page

Grid  List 

Set Descending Direction